Peerless PO13 Oilless Series Single Phase Air Compressor – Direct Drive Portable – 1.5kW / 2.0HP – 12CFM/175LPM – Tank Mount
This impressive Peerless Oilless 13 Air Compressor – 175LPM of free air delivery, this will run your framing guns through to your coil guns. We have also fitted an electronic auto drain to the receiver, as we all know its hard to remember to drain your tank, so we fitted this little feature. Along with this that drives this air compressor is a 2HP copper wound motor, this is where the weight comes into it as the motor itself weighs 19kg. This is the easiest way to know if your oil less motor is an actual 2HP. Being an Oil Less Air Compressor it doesn’t matter about parking level too! compared to oiled Air Compressors. Drawing an impressive 6AMPS compared to 8AMPS on other models this is well suited for low voltage areas!.
Check CFM Conversions:
Peerless PO13 Oilless Series Single Phase Air Compressor - Direct Drive Portable - 1.5kW / 2.0HP - 12CFM/175LPM - Tank Mount
Peerless PO13 Oilless Series Single Phase Air Compressor - Direct Drive Portable - 1.5kW / 2.0HP - 12CFM/175LPM - Tank Mount
Description
Peerless oil-less range of air compressors are very reliable, cost-efficient and clean.
Copper wound electric motors with 7AMP draw producing an outstanding air flow of free air delivery along with its super quiet motor at only 52dBa +/-2.
This impressive Air Compressor produces 175LPM of free air delivery, this will run your framing guns through to your coil guns.
We have also fitted an electronic auto drain to the receiver on the standard model (00590), as we all know its hard to remember to drain your tank. The 2HP motor / pump assembly is fully copper wound. This is where the weight comes into it, as the motor itself weighs 19kg. This is the easiest way to know if your oil less motor is an actual 2HP.
An over run cut out alarm is a new feature fitted to our PO13. This is to assist in making sure your air compressor doesn’t get damaged due to excessive running caused by air leaks or the air tool being too big for the unit. Protecting your investment and keeping it in top performance is our goal.
American Teflon barrels and piston rings deliver maximum performance and life span. These have to be serviced based upon hours of use. Being oil free doesn’t mean maintenance free – despite what any will tell you. On average they need to be replaced every 2000 Hours of use. Cheaper units are 500 hours of use dependent on material used in manufacturing process. We carry all spare parts and components to be able to service and maintain your air compressor. They are not a throw away air compressor, we believe in making sure your down time isn’t impacted, as down time is costly.
Being an Oil Less Air Compressor it doesn’t matter about parking level too! compared to oiled Air Compressors. Drawing an impressive 7AMPS compared to 9AMPS on other models this is well suited for low voltage areas!
Did you know?
In standard environment conditions when your air compressor reaches 14 PSI you have the reached the volume of air in the receiver!. So on this particular model (PO13) at 14 PSI you have 30L of compressed air in the tank. At 28 PSI you now have 60L of compressed air in the tank. So if the cut out pressure is 112 PSI, you now have 240L of stored compressed air! Who said small tanks don’t hold enough air?
As mentioned this can be affected by the temperature and other factors.
Smaller tanks also equates to quicker air recovery times of lost pressure along with lower operating temperature of pump.
Important
Please note: air compressors i.e piston type, are not designed to run continuously they must cut in and out. Direct drive models should only have up to a 40-50% duty cycle. Belt Drive hobby models are up to 60-70% and full industrial belt drive models are up to 75-85%. If the compressor runs over these duty cycles it could cause failure. Important – first check voltage on each building site as low voltage will cause the motor to fail on all compressors. It must have be better than 230 volt at peak times. Extension leads will cause voltage drop, it’s better to use extra air hose.
Specification
| Code | 00590 |
| Model | PO13 |
| Free Air Delivery (LPM) | 175 LPM |
| Max PSI | 145 |
| Motor HP | 2 |
| Warranty pump | 1 Year |
| Warranty motor | 1 Year |
| Tank capacity (L) | 40L |
| Pump uptime to 100PSI | 1.05 – 1.10 Min |
| Cooling method | Air cooled |
| Pump type | Oil-less Copper wound |
| Cylinders | 2 |
| Pump head tension | 7.8 FT LB11 NM |
| Oil capacity | – |
| Pump RPM | 1350 |
| Outlet thread | 1/4″ BSP |
| Electricity | 240V / 10A |
| Amps draw | 7 |
| Dimensions |
810 x 340 x 640 mm
|
| Weight | 33 kg |
Frequently Asked Questions
Should I purchase industrial machinery from a tool shop or reseller, or from an industrial machinery specialist?
What after-sales support and warranty do you provide?
- Application support: Whether your requirements are straightforward or highly specific, we work with you to ensure your machine is set up and performing for your exact application, and we are here to help as your needs evolve.
- Pre-dispatch testing: Every machine is fully checked and commissioned before it leaves us. It's a step that saves our customers countless issues down the track and sets your machine up for maximum uptime.
- Warranty: We don't just pass on the manufacturer's warranty. We offer our own comprehensive warranty that goes further, giving you greater coverage and peace of mind, with extended warranty options also available.
- Spare parts: Downtime costs you money, so minimising it is our priority. We keep a wide range of parts and consumables in stock, and if we don't have it on the shelf, we will track it down and get it to you as fast as possible.
- Remote support: Fast help via phone, email, or live video, with no site visit needed in most cases. We pride ourselves on some of the fastest response times in the industry, because we know that when you need help, you need it now.
- On-site service: Our engineers travel Australia-wide, with trusted contractors covering remote areas.
- In-house repairs: Send your machine back to us for expert servicing and overhaul.
How quickly will I receive my machine?
Specification
Additional information
| Weight | 43 kg |
|---|---|
| Dimensions | 91 × 44 × 74 cm |
| Compressor Type | |
| Dryer Configuration | |
| Pump Motor | |
| Motor size | |
| Compressor Type (Air End) | |
| Air Quality / Lubrication | |
| Mount Type | |
| CFM | |
| LPM | |
| Kilowatt (kW) | |
| Horse Power (HP) | |
| Voltage Supply Type | |
| Power Source |














Reviews
There are no reviews yet.